1995 Subaru oil sending unit ?

Where is oil sending unit located and how to replace it on 1995 Subaru car model.

The details with proper diagrams are as follows-----

The oil pressure switch is attached to the crankcase (1.2L engine), oil pump case (1.6L, 1.8L and 2.7L engines) or cylinder block (2.2L, 2.5L and 3.3L engines). It monitors oil pressure and activates the oil pressure indicator light in the combination meter.

See the diagram shown below:------




The sensor is made up of a diaphragm which is operated by oil pressure. A set of contacts open and close in relation to the diaphragm movement. The entire sensor is encased in phenol resin which is not effected by temperature or oil. The sensor is not serviceable, and must be replaced if found to be defective.




Before replacing the Oil pressure sensor switch,test the sensor to confirm its faulty.
Te procedure to test is as follows:-----

TESTING

1. Remove the oil pressure switch from the engine.

2. Install a T-fitting into the oil pressure switch hole and connect the oil pressure switch to one end, and a suitable oil pressure gauge to the other.

3. Start the vehicle and allow it to reach normal operating temperature. Upon starting the vehicle, the oil pressure light should illuminate. If it does not, check the wiring to the indicator lamp for power.

4. At an oil pressure of 2.1 psi (15 kPa), the oil pressure indicator light should go out. If the light does not go out, replace the oil pressure switch.

One the Oil pressure sensor switch is checked faulty,then replace it.The procedure to remove and install oil pressure sensor switch is as follows:-----

REMOVAL & INSTALLATION

1. Disconnect the negative battery cable.
2. Access the oil pressure switch on the crankcase (1.2L engine), oil pump case (1.6L, 1.8L and 2.7L engines) or cylinder head (2.2L, 2.5L and 3.3L engines). Unfasten the wire harness from the switch.
3. Place a suitable drain pan underneath the oil pressure switch to capture any oil which may spill out during the removal and installation of the switch.
4. Use an appropriate wrench or socket to loosen and remove the oil pressure switch. If reinstalling original oil pressure switch, remove and discard washer on switch.

To install:

5. Position the oil pressure switch and new washer into hole on crankcase, oil pump case or cylinder head, depending on models, and hand-tighten.
6. Use an appropriate socket and tighten the oil pressure switch to 12-17 ft. lbs. (17-23 Nm).
7. Fasten the wire harness to the oil pressure switch.
8. Connect the negative battery cable.
9. Check the oil level and add oil if needed.

This details will help.

Thanks.

For All types of Car models and brands help 
Go to Newly Launched
FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

where is oil sending unit located on 2006 hyundai accent?

Oil  pressure sending unit measures the engine oil pressure and sends this information to the oil pressure gauge.
For 2006 Hyundai Accent  its mounted on the oil filter housing just above the filter.And below the Alternator.
The filter  is located directly under the engine it is in plain view if you look under it.
The oil pressure sensor is on the front of the block on the right side, right above the crank sensor.

See the image shown below,this is how it looks:-----


This will help.
Thanks.

For All types of Car models and brands help 

Go to Newly Launched
FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html