GMC Envoy 02-05 Stereo Removal
Step 1: Engage parking brake.
GMC Envoy 02-05 Stereo Removal
Step 2: Remove screw in cupholder.
GMC Envoy 02-05 Stereo Removal
Step 3: Remove screws from front center of console.
GMC Envoy 02-05 Stereo Removal
Step 4: Remove rubber tray and screws from rear of console.
GMC Envoy 02-05 Stereo Removal
Step 5: Remove rubber mat from bottom of center console. Remove screws.
GMC Envoy 02-05 Stereo Removal
Step 6: Remove the center console tray piece and remove screws below. Pull entire center console towards rear of vehicle.
GMC Envoy 02-05 Stereo Removal
Step 7: Remove screws from both sides of carpeted panel below radio. Remove the carpeted panel.
GMC Envoy 02-05 Stereo Removal
Step 8: Remove 2 screws at botton of radio trim bezel.
GMC Envoy 02-05 Stereo Removal
Step 9: Unclip radio trim bezel.
GMC Envoy 02-05 Stereo Removal
Step 10: Remove screws and plugs from radio.
GMC Envoy 02-05 Stereo Removal
GMC Canyon 04-09 Stereo Removal
Step 1: Unclip trim around radio.
GMC Canyon 04-09 Stereo Removal
Step 2: Remove 3 7mm bolts securing radio to vehicle.
GMC Canyon 04-09 Stereo Removal
Bezel Assembly
- Use a flat-bladed plastic trim tool to release the retainer clips along the rear edge of the bezel.
- Lift the bezel out of the console assembly.
- If replacing the front floor console bezel assembly, transfer all necessary components.
----------------------
IMPORTANT: Do not grab or pull on the CD storage door when removing the trim bezel.
Remove the screws securing the trim bezel to the console extension.
Protect the console extension from damage then carefully use a small prying device to push in the tabs underneath the trim bezel securing the top of the trim bezel.
Remove the trim bezel.
To remove the bezel on the luxury console, refer to Bezel Replacement - Floor Console (Luxury) in Instrument Panel, Gages and Console.
Use a small screwdriver in order to release the CD player retainers.
Slide the CD player out.
Disconnect the electrical connector.
INSTALLATION PROCEDURE
Connect the electrical connector.
Install the CD player.
When the CD player is fully seated, snap the unit into the retainers.
To install the bezel on the luxury console, refer to Bezel Replacement - Floor Console (Luxury) in Instrument Panel, Gages and Console.
NOTE: Refer to Fastener Notice in Service Precautions.
Install the trim bezel and the screws.
Tighten
Tighten the screws to 2 N.m (18 lb in ).
Open the rear cup holder on the console and pull it out all the way. Then open up the lid to the console.
Grab on either side of the center pocket of the console and lift it up with your hands. It's held in place by gravity and friction, so it should be fairly easy to lift out of place.
Locate the four bolts that hold the console to the floor. They're in both the front and back of the console, right in the middle on metal braces.
Unbolt the console from the floor using the 3/8-inch ratchet, extension and sockets. You may have to alternate between using the extension and not, depending on how far you can reach your arm.
Lift the console out of the vehicle and place it to the side.
----------
Disable the Airbag, or SRS System
Turn the steering wheel so the wheels are facing straight ahead. Turn the ignition to the Lock position and remove the key.
Remove the fuse cover from the end of the instrument panel on the driver's side. Consult the legend on the cover and remove the fuse that protects the airbag circuit. Wait at least two minutes while the system depletes the back-up power supply.
Remove the screws that secure the driver's knee bolster with a Phillips screwdriver and pull it away from the dash. Pull the driver's airbag electrical connector out of the terminal at the steering column.
Open the glove box and pull the passenger airbag electrical connector out of the terminal.
Remove the Seats
Slide the driver's seat all the way forward on its runner. Locate the floor-to-rail bolts on each side of the runner and remove them with a socket wrench.
Slide the seat all the way backwards on the runner and remove the rear floor-to-rail bolts in the same way.
Lift the seat up and remove it from the vehicle.
Repeat the procedure with the passenger seat and remove it from the vehicle.
Remove the Center Console
Locate the mounting bolts on the four corners of the console support.
Remove the bolts with a socket wrench.
Lift the console up and out of the vehicle.
To reinstall the seats, follow the steps for removal in reverse order.
No comments:
Post a Comment